EXTERNAL WALL WATERPROOFING

Product Details:

Starproof WF-AB-602 is High performance coldapplied single component waterproofing membrane,specially designed from a blend of special resin and rubber,reinforced with special water repelling fillers, mineralsstabilizers and gelling agent. STARPROOF WF-AB-602can be applied over several types of substrates aswaterproofing and protective coating for concrete andmasonary.

Application:

• Suitable for waterproofing and protection for wet areas, kitchens and substructures.
• Vapor barrier coating for walls and floor.
• Waterproofing system for shaded or tiled roofs.
• Waterproofing for polyurethane foam slab
• Waterproofing for polyester built up roofs
• Maintenance of existing roofs, masonry and concrete Walls.
• Apply two coats at rate of 0.8-1 kg/ m2 to provide a total thickness of minimum 1.5 mm.
• Stir the contents of drum thoroughly to remove all sediments.
• Apply material to achieve required thickness at an interval of 24 hours at room temperature.
• At joints and detailing, apply a layer of mesh reinforcement while the first coat is wet. If needed you can apply the mesh reinforcement all over the application area.
• Allow 24 hours for curing.

Advantages:

• Single component, easy to apply, no need for mixing or heating.
• Elastomeric bridge minor cracks which may occur in concrete substrate.
• High tensile strength and elongation.
• Excellent adhesion to substrate.
• Highly elastic product and cures to rubber like membrane.
• Capable of withstanding severe causes of expansion, contraction and deck movements.
• Excellent UV Resistance, oxidation and ozone.
• Resistance to peeling, chipping and/or separation and longer life.

Directions For Use:

• The surface must be thoroughly cleaned and should be free of dirt, gravel, dust and oil. The concrete should be dry and smooth. Concrete shall be at least 28 days old, fully cured and well dry. All holes shall be repaired by proper cementitious mortar prior to application.

Priming:

• No need for primer coat prior to applying the STARPROOF WF-AB-602. IF NEEDED, and in case of dusty surface, a prime coat can be applied by diluting STARPROOF WFAB-602 with water and applying a prime coat. Wait for the coat to dry prior to application.

Coverage:

• Theoretical coverage of STARPROOF WF-AB-602 is approximately 1 m2/ ltr., at 800 microns.

Storage:

• Store away from sunlight and preferably below 30°C.
• Storage should be frost protected.

Health & Safety:

• As with all chemicals, caution should always beexercised. Protective clothing such as gloves andgoggles should be worn.

Inhalation:

• Inhalation of vapor or mist should beavoided. If inhaled symptoms include coughing,wheezing, laryngitis, and shortness of breath, headache,nausea, and vomiting. Immediately shift victim to freshair, and, if needed immediately start artificial respiration.Give oxygen if breathing is labored. Get emergencymedical help.

Eye Contact:

• Flush eyes with water for 15 minutesand call for medical help.

Ingestion:

• Causes nausea, vomiting, and loss ofconsciousness. If accidentally swallowed do not inducevomiting rather call for medical help immediately.

Product Details:

Dr. Fixit Raincoat is composed of high quality acrylic emulsion polymer, light fast & weather durable pigments, properly selected & graded fine fillers, many additives & water as a medium. It is used as a waterproofing & protective coating for exterior walls of the buildings because it forms higher film thickness, has excellent flexibility, breathing properties, water resistance, crack-bridging ability, weathering durability and an excellent resistance to the growth of microorganisms.

Areas of Application:

• All types of exterior masonry surfaces, concrete, cement sand renderings, etc.
• Applicable on asbestos sheets.

Features & Benefits:

• Film thickness - Higher film thickness provides resistance to the movements of structures, gives crack bridging ability & waterproofing properties.
• Flexibility - Flexible and covers hairline cracks(upto 0.5 mm) effectively so that no ingress of water.
• Toughness - Tough films withstands wind driven rain.
• Elasticity - High elasticity easily withstands stress caused by thermal expansion & contraction (>100% elongation at 110-120 micron DFT).
• Ready to use – No dilution is required hence ensures desired film thickness built-up without affecting the performance.
• Microbial resistance – Resistance to fungus and algae hence maintains the aesthetic value.
• UV resistant – Resistance to UV (Sun light) hence coating has longer life.
• Dirt pick up – Very low dirt pick up & can be cleaned easily hence maintains the aesthetics.
• Breathability - Permeable to water vapour.
• Ease of application – User friendly, easily applicable by brush, roller or spray.
• Toxicity - It is Non-toxic.

Method of Application:
Surface Preparation:

• All new cement-sand renderings /concrete surfaces should be allowed to age 6 to 8 weeks before surface coating.
• Surface for treatment must be thoroughly cleaned of all laitance, loose material, oil, grease, etc. by mechanical means such as wire brushing & shot blasting.
• Finally vacuum cleaning of all loose solids and liquids can be done, if required.
• All surface cracks upto 5 mm width should be filled up with Dr.Fixit Crack-X or Dr.Fixit Unifiller. Cracks more than 5 mm and all separation gaps should be filled up with Dr.Fixit Pidicrete URP or Dr.Fixit Unibond SBR modified mortar or as specified.

Priming:

• Prime the surface with Dr. Fixit Primeseal diluted with potable water by volume in 2:1 ratio (2 parts primer and 1 part water) and allow it to dry for 2 to 3 hours.

Application:

• Use Raincoat directly from the container. Stir contents well before use.
• Apply two neat coats of Raincoat without dilution by brush or roller at a time interval of 5-6 hours.
• For enhanced protection, apply additional coat of Raincoat on rain lashing walls, chajjas and parapet walls.
• Allow the coated surface to air cure fully for 7 days.

Precautions & Limitations:

• Do not dilute Dr. Fixit Raincoat.
• Recommended to be primed with Dr. Fixit Primeseal only.
• Do not apply when ambient temperature is below 100C or above 450C.
• Do not apply in direct sunlight or during rains.
• Adhesion property may get affected over poor quality putty and very smooth surfaces

Product Details:

Dr. Fixit Raincoat Coool is a heat reducing & ‘Energy Saving’ acrylic waterproofing coating . It is composed of specially selected reflective additives, light fast & weather durable pigments & graded inert fillers. It is a solar reflective coating on exterior walls which helps in reduction of enery usages by less heat transfer into buildings & keeps the interiors cool . The coating serve the dual purpose of thermal reduction & with additional waterproofing protection.

Areas of Application:

• All types of exterior masonry surfaces, concrete, cement sand renderings, etc.

Features & Benefits:

• Solar Reflective - Re-radiates most of solar heat back into atmosphere, thus lowers the surface temperature.
• Durability - Provides long time protection to building that are endangered due to thermal degradation
• Waterproofing - Excellent waterproofing increases the durability of structure
• Shades – Available in wide range of pastel & selective dark shades
• Elastomeric - High elasticity withstand stress caused by thermal expansion & contraction.
• Microbial resistance - Resistance to fungus and algae growth, hence maintains the aesthetic of buildings.
• Eco friendly -Non Toxic water based system
• Energy Saving – Low heat transfer into building hence reduction in electrical consumption
• Ready to use – No dilution is required.
• Substrate temperature reduction up to 8ºC.

Method of Application:Surface Preparation on Cementitious Surfaces:

• All new cement-sand renderings /concrete surfaces should be allowed to age 6 to 8 weeks before surface coating.
• Surface for treatment must be thoroughly cleaned of all laitance, loose material, oil, grease, etc. by mechanical means such as wire brushing & shot blasting. Finally vacuum cleaning of all loose solids and liquids can be done, if required.
• All surface cracks up to 5 mm width should be filled up with Dr. Fixit Crack-X.
• Cracks more than 5 mm and all separation gaps should be filled up with Dr. Fixit Pidicrete URP modified mortar or as specified.

Priming:

• Attain SSD condition before priming, Prime with Dr. Fixit Primeseal (2 part primer : 1 part water)
• Apply with brush or roller

Application:

• Use Dr. Fixit Raincoat Coool directly from the container. Stir contents well before use.
• Apply 2 coats of Dr. Fixit Raincoat Coool without any dilution by brush or roller at an interval of 5-6 hours.
• For enhanced protection, apply additional coat of Dr. Fixit Raincoat Coool on rain lashing walls, chajjas and parapet walls.
• Allow the coated surface to air cure fully for 7 days.

Precautions & Limitations:

• Do not dilute.
• Always to be kept as final coat. i.e. No overcoating on Dr. Fixit Raincoat Coool.
• Do not apply when ambient temperature is below 10°C or above 45°C.
• Do not apply in direct sunlight or during rains.
• Adhesion property may get affected over putty and very smooth surfaces.

Shelf Life & Storage:

• Shelf life is 24 months from the date of manufacturing in unopened conditions.
• Store in a cool and dry place.
• Keep away from direct sunlight and heat.

Health & Safety Precautions:

• Skin Contact: Wash skin with soap & water. Remove contaminated clothes
• On eye contact: Immediately splash eyes with plenty of water. Consult Physician if irritation persists.

Product Details:

Zycosil+ is a clear, water soluble, concentrated, penetrating sealer based on organosilane technology. Deep penetration and reaction with the substrate provides long term water proofing for up to 20 years. Zycosil Multi Surface Sealer protects surfaces from structural and aesthetic damage such as efflorescence, and structural freeze thaw. It also reduces the damaging effects of water penetration to steel.

BASIC USE:
Recommended for use on:

• Masonry Block (CMU)
• Brick
• Concrete
• Unsealed Stucco
• Sand and dirt
• Plaster
• Grout
• Aggregates
• Pavers
• Cement tile

Features/Benefits:

• Water based, no harmful solvents, meets the stringent VOC Standards of California.
• Easy application by spray, brush or roll
• No masking required if windows and metal trim are clean
• Greater coverage per gallon than competitive sealers
• Dries clear, does not alter substrate appearance
• Faster reaction time than typical sealers
• Breathable
• Reduces mold and mildew growth
• Reduces material and labor costs

Product Details:

DescriptionDr. Fixit Sureseal is a specially designed waterproof coating once which cured forms breathable, very tough yetelastic film which develops strong bonding to damp surfaces. It is ideal for patch repair of internal and externalwalls as well as temporary patch repair of roofs. This product offers excellent protection for repaired surfaces andeffectively covers hairline cracks.Typical Applications} Mild damp surfaces of following kind - internal walls, external walls, screed roofs, parapets, chajjas etc.Features} Very tough yet elastic and breathable film} Provides strongly bonded waterproof coating} No dilution required, ready to use} Tintable and can be used over painted surfaces} Prevents Mildew, Fungal & bad odour

Additional Information:

• Delivery Time: 3 WORKING DAYS

Product Details:

Description Dr. Fixit Raincoat Waterproof Coating is composed of high quality emulsion polymer, weather durable pigments, properly selected & graded fine fillers, additives & biocides. It is used as a waterproofing & protective coating for exterior walls of the buildings.Typical Applications }} All types of exterior masonry surfaces, concrete, cement sand renderings, etc. }} Applicable on cement sheets.Features }} Flexible covers hairline cracks (up to 0.5 mm) effectively, thus prevents ingress of water. }} Toughness – Tough film withstands wind driven rain. }} Ready to use – No dilution is required. }} Breathability – Permeable to water vapour. }} Ease of application – User friendly, easily applicable by brush, roller or spray. }} Non toxic – Eco Friendly. }} Primer – Can act as a primer cum waterproofing coating for all water based exterior paints.

Additional Information:

• Delivery Time: 3 WORKING DAYS